Nuestra web utiliza cookies para asegurar la mejor experiencia al usuario. Para continuar navegando en nuestra web, usted está aceptando el uso de cookies. Más información

cerca Close Cookie Notification
Instron
  • Back
  • Home
  • Productos
    SISTEMAS DE ENSAYO
    Sistemas de ensayo universales
    Durabilidad estructural
    Sistemas de ensayo automatizados
    Sistemas de ensayo dinámicos y de fatiga
    Simulación de impacto
    Sistemas de ensayo de torsión
    Péndulos y torres de impacto
    Reómetros y medidores de fluidez
    HDT y Vicat
    Sistemas fuera de producción
    ACCESORIOS
    Software
    Mordazas de tracción
    Pelado, fricción y punzonado
    Cámaras ambientales y hornos
    Células de carga
    Fijaciones de flexión
    Platos de compresión
    Fijaciones para el sector biomédico y farmacéutico
    Extensómetros
    Células de carga
    Fijaciones para la microelectrónica
    Medición y preparación de probetas
    Todos los accesorios
    Catálogo de accesorios
  • Soluciones Industriales
    Mordazas de tracción POR NORMATIVA POR TIPO DE ENSAYO
    POR SECTOR
    Sector aeroespacial
    Sector automotriz
    Sector biomédico
    Sector electrónico
    MATERIALES
    Composicion
    Rieles
    Plástica
  • Servicio y soporte
    Instron Remote Technical Support CICLO DE VIDA DEL PRODUCTO
    SERVICIOS
    Calibración y verificación
    Ayuda en la implementación de Instron
    Mantenimiento preventivo
    Instalación y reubicación
    Reparación y renovación
    Actualizaciones
    FORMACIÓN
    Formación in situ en sus instalaciones
    Secretos para Ensayos Fiables
    SOPORTE TÉCNICO
    Preguntas frecuentes
    Servicios de actualización de software
    RECURSOS
    Localizador de número de serie
    Manuales
  • Nuestra empresa
    EMPLEO SALA DE PRENSA SUSCRÍBASE A NUESTRO BOLETÍN DE NOTICIAS
    ACERCA DE NOSOTROS
    Nuestra historia
    Localización
    Certificados y acreditaciones
    RECURSOS
    Glosario
    Tipos de ensayo
    Estudios de caso
    Biblioteca de documentación
    Noticias
    Eventos
    Seminarios web
    Boletines informativos
    Términos y privacidad
    Accesibilidad
    Aviso de cookies
    Aviso de privacidad de datos GDPR
    Control de exportación
    Aviso de Privacidad
    Términos y condiciones
    Condiciones de uso
  • Contacto
  • España
Opciones de ensayos » By Test Type » Reología » ISO 1133-2 & ASTM D1238

ISO 1133-2 and ASTM D1238: When Load Cell Ensures Repeatability of Results

Normas

  • ISO 1133
  • ASTM D1238

Tipo de probeta

  • Pellets
  • Powder

Tipos de ensayos

  • Rheology

Materiales

  • Plastics
  • Caucho/Elastómeros

Sector de negocio

  • Productos de consumo/industriales
  • Subcontratación de ensayos
ContáctenosView Accessories Catalog
  • DESCRIPCIÓN
  • Literature

Melt Flow Rate (MFR) and Melt Volume-Flow Rate (MVR) can normally be obtained with easy and quick test procedures. Test standards specify detailed test conditions, including pre-heating period, starting position, and measurement length/time. However, when using a basic melt flow tester (extrusion plastometer), fulfilling all standard specifications can be challenging with some polymers and compounds, and results can be affected by poor repeatability.

It's not uncommon that during the pre-heating period the sample swells and pushes the piston up, especially when testing under low-load conditions (e.g. less than 2.16 kg). Applying a compacting force higher than the test weight can prevent this from happening, and if precise positioning of weight lifting device is possible, the starting position and timing for measurements can be set in a much more repeatable way.

Some samples show very high viscosity and effective compacting requires high loads. Air bubbles trapped inside as a result of poor compacting can affect the MFR/MVR results. A high, but controlled, compacting force is needed. Plus, at the end of tests, the same force can be applied for purging out the remaining material, reducing the total test cycle time.

We tested an HDPE sample with an expected MFR of about 0.25 g/10 min (190 °C, 2.16 kg) with a CEAST MF30, applying ISO 1133-2 Procedure B. CEAST MF30 has a load cell integrated with the weight lifting device, giving the possibility to apply up to 750 N of compacting force. To compare the repeatability of results, we performed twenty consecutive tests using the load cell for compacting, and another twenty without (so using only the test weight to compact). The average MFR result was close to the expected value in both cases. However, results from the tests performed without the load cell were consistently higher and with a standard deviation of 0.012 g/10 min (close to 5%), whereas tests where the load cell was compacted the standard deviation was as low as 0.005 g/10 min (2%). Similar results were obtained also following ASTM D1238 Procedure B.

CEAST Melt Flow Series Brochure

Flow properties of molten plastics are a critical characteristic requiring good knowledge and control. The Instron® Melt Flow Testers are specifically designed for easy and accurate measuring of the Melt Mass-Flow Rate (MFR) and the Melt Volume-Flow Rate (MVR). CEAST Melt Flow Testers range from systems that perform a simple manual test procedure to semi-automated testing systems performing multiple weight tests.

  • Productos
  • 7/3/2013
  • 1.1 MB

Selección Zona

Dismiss Region Selector

Americas

  • North America
  • Brasil
  • South America

All Other Countries

  • Global Site

Europe

  • France
  • Deutschland
  • Italia
  • Polska
  • España
  • Türkçe
  • United Kingdom

Asia Pacific

  • 中国
  • India
  • 日本
  • 대한민국
  • 台灣
  • ประเทศไทย
Instron Logo White
INFORMACIÓN DE CONTACTO

C/ Argenters 2,
Parque Tecnológico del Vallés,
08290 Cerdanyola,
Barcelona, Spain

General: +34 935 947 560

ENLACES ÚTILES
  • Sistemas de ensayo
  • Software
  • Accesorios
  • Catálogo
  • Biblioteca
  • Soluciones de ensayos
  • Seminarios web
  • Estudios de caso
  • Eventos
  • Empleo
  • Glosario
  • Noticias
Policies / Legal
  • Privacidad y política de cookies
  • Condiciones de uso
  • Control de exportación
  • Aviso de datos (RGPD)
CONECTE CON NOSOTROS
SUSCRÍBASE A NUESTRO BOLETÍN DE NOTICIAS
DIRECCIÓN DE CORREO ELECTRÓNICO
© Illinois Tool Works Inc. Todos los derechos reservados.
[email protected]
  • Privacidad y política de cookies
  • Condiciones de uso
  • Control de exportación
  • Aviso de datos (RGPD)