Nuestra web utiliza cookies para asegurar la mejor experiencia al usuario. Para continuar navegando en nuestra web, usted está aceptando el uso de cookies. Más información

cerca Close Cookie Notification
Instron
  • Back
  • Home
  • Productos
    SISTEMAS DE ENSAYO
    Sistemas de ensayo universales
    Durabilidad estructural
    Sistemas de ensayo automatizados
    Sistemas de ensayo dinámicos y de fatiga
    Simulación de impacto
    Sistemas de ensayo de torsión
    Péndulos y torres de impacto
    Reómetros y medidores de fluidez
    HDT y Vicat
    Sistemas fuera de producción
    ACCESORIOS
    Software
    Mordazas de tracción
    Pelado, fricción y punzonado
    Cámaras ambientales y hornos
    Células de carga
    Fijaciones de flexión
    Platos de compresión
    Fijaciones para el sector biomédico y farmacéutico
    Extensómetros
    Células de carga
    Fijaciones para la microelectrónica
    Medición y preparación de probetas
    Todos los accesorios
    Catálogo de accesorios
  • Soluciones Industriales
    Mordazas de tracción POR NORMATIVA POR TIPO DE ENSAYO
    POR SECTOR
    Sector aeroespacial
    Sector automotriz
    Sector biomédico
    Sector electrónico
    MATERIALES
    Composicion
    Rieles
    Plástica
  • Servicio y soporte
    Instron Remote Technical Support CICLO DE VIDA DEL PRODUCTO
    SERVICIOS
    Calibración y verificación
    Ayuda en la implementación de Instron
    Mantenimiento preventivo
    Instalación y reubicación
    Reparación y renovación
    Actualizaciones
    FORMACIÓN
    Formación in situ en sus instalaciones
    Secretos para Ensayos Fiables
    SOPORTE TÉCNICO
    Preguntas frecuentes
    Servicios de actualización de software
    RECURSOS
    Localizador de número de serie
    Manuales
  • Nuestra empresa
    EMPLEO SALA DE PRENSA SUSCRÍBASE A NUESTRO BOLETÍN DE NOTICIAS
    ACERCA DE NOSOTROS
    Nuestra historia
    Localización
    Certificados y acreditaciones
    RECURSOS
    Glosario
    Tipos de ensayo
    Estudios de caso
    Biblioteca de documentación
    Noticias
    Eventos
    Seminarios web
    Boletines informativos
    Términos y privacidad
    Accesibilidad
    Aviso de cookies
    Aviso de privacidad de datos GDPR
    Control de exportación
    Aviso de Privacidad
    Términos y condiciones
    Condiciones de uso
  • Contacto
  • España
Productos » Sistemas de ensayo » Structural Durability » Structural Durability Solutions » Full Vehicle Test System

Full Vehicle Test System

Menu
  • Structural Durability Solutions
    • Axle Test System
    • Component Test Systems
    • Dynamic Torsion Test System
    • Full Vehicle Test System
    • Road Simulator
    • Multi-Axis Shaking Table (MAST)
    • Shock Absorber Test Systems
    • Biaxial Wheel Test System (ZWARP)
Contact Us
  • DESCRIPCIÓN
  • Related Products
  • Software

Challenge

A high level of vehicle reliability is assumed by the buyer. To ensure this reliability, it requires comprehensive knowledge of the operating loads and environmental conditions that must be considered in the design of a vehicle. In addition to load measurements and field measurements which are used to build up computational simulations, experimental proofs of the operational strength of prototypes and assemblies are necessary to ensure their results. Various system and component test systems are used. 

The complexity of the service loads requires the use of multi channel test rigs, which allow us to investigate the lifetime and to explore the entire systems under vertical and horizontal loads, even with simultaneous simulation of environmental conditions.

Solution

Modern full-vehicle test allow life-time detection of car body areas and are mainly stressed by horizontally introduced operating loads. This is not possible with conventional 4-cylinder road simulators, since only the vertical component of an inaccessible road section is simulated with these test stands, and thus a realistic body fatigue can only be determined to a limited extent. Loads caused by driving maneuvers, e.g. Longitudinal, braking and lateral forces can only be detected by a multi-test system test stand, such as full vehicle test rig.

In addition to durability analyzes of the body, chassis components such as, for example, engine mounts, exhaust systems, and entire assemblies. Instron offers comprehensive solutions with and without vehicle restraint, with long- or short-stroke introduction of lateral forces as well as the optional environmental simulation with regard to temperature humidity and sun loading.

Controller Labtronic® 8800ml

Labtronic 8800ml, Instrons new test controller, provides an integrated laboratory solution for all requirements from component tests through to simulation of service loads on full vehicles.

Hydropuls® actuators

Hydropuls hydraulic actuators are used in the full of static and dynamic applications where high precision simulation of movement, forces, strains and accelerations are required.

Power Packs and accessories

A modular range of variable flow hydraulic power supplies are available to service dedicated test systems or to be configured as a central laboratory supply facility. Pipeline solutions are also available to safely distribute the hydraulic supply around the lab.

Sensors

A comprehensive range of fatigue rated precision transducers are available to measure position, force, torque, pressure, strain and acceleration.

Servo valves

To deliver the full range of actuator performance requirements, a range of 2 and 3 stage servo valves with flow rates from 5 liters to 2400 liters/min are available.

RSLabSite modulogic

All you need for your durability tests is the measurement data obtained from the proving ground – RS LabSite® modulogic will do the rest!

Selección Zona

Dismiss Region Selector

Americas

  • North America
  • Brasil
  • South America

All Other Countries

  • Global Site

Europe

  • France
  • Deutschland
  • Italia
  • Polska
  • España
  • Türkçe
  • United Kingdom

Asia Pacific

  • 中国
  • India
  • 日本
  • 대한민국
  • 台灣
  • ประเทศไทย
Instron Logo White
INFORMACIÓN DE CONTACTO

C/ Argenters 2,
Parque Tecnológico del Vallés,
08290 Cerdanyola,
Barcelona, Spain

General: +34 935 947 560

ENLACES ÚTILES
  • Sistemas de ensayo
  • Software
  • Accesorios
  • Catálogo
  • Biblioteca
  • Soluciones de ensayos
  • Seminarios web
  • Estudios de caso
  • Eventos
  • Empleo
  • Glosario
  • Noticias
Policies / Legal
  • Privacidad y política de cookies
  • Condiciones de uso
  • Control de exportación
  • Aviso de datos (RGPD)
CONECTE CON NOSOTROS
SUSCRÍBASE A NUESTRO BOLETÍN DE NOTICIAS
DIRECCIÓN DE CORREO ELECTRÓNICO
© Illinois Tool Works Inc. Todos los derechos reservados.
[email protected]
  • Privacidad y política de cookies
  • Condiciones de uso
  • Control de exportación
  • Aviso de datos (RGPD)